View AN501_234629.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AN501
Vishay Siliconix
The DG535/536 Wideband Multiplexers Suit a Wide Variety of Applications
Introduction Analog switch IC's traditionally have found limited use in applications involving high-frequency analog or digital signals. Degradation of switch performance and intolerable signal cross-talk between channels has undoubtedly forced many designers to use bulky electromechanical switches or costly discrete designs. At best, analog switch ICs configured in L or T arrangement could be adopted. However, increased board space and layout complexity became major problems in configuring systems with high channel density. The DG535/536 are compact 16-channel, single-ended multiplexer ICs, primarily designed as a cost-effective solution to video and wideband switching problems. Other applications that benefit from the devices' superior performance characteristics are: S Digital switching S Audio Switching
S PCM routing networks S ATE systems S High-channel-density multiplexing or demultiplexing systems S High-speed multiplexing systems S Low-level signal multiplexing
Product Description A functional block diagram of the DG535/536 is shown in Figure 1 and the switch configuration is shown in Figure 2. The device is fabricated using self-isolated, silicon-gate D/CMOS technology. This process enables the logic interface and driver circuitry, the gating and latching stages, and the switching elements to be combined in a monolithic structure. Ease of design for large switching matrices and interface with microprocessors is accomplished with comprehensive logic gating and latching functions available on the chip.
V+ S1
GND
SW1 S1 SW2
SW3 S2 SW4
S8 S9
D `T' Switch Configuration
S8 D S9 SW5
S16 Decoders/Drivers Gating Logic DIS S16
S15
Latches
1st Level EN CS CS A3 A2 A1 A0 ST
2nd Level
FIGURE 1. DG535/536 Functional Block Diagram
Document Number: 70608 03-Aug-99
FIGURE 2. Switch Configuration
www.vishay.com S FaxBack 408-970-5600
6-1
AN501
Vishay Siliconix
The DG536 is housed in a small, 44-pin J-lead package, thus minimizing board size requirements. The DG535 is packaged in a 28-pin DIP. Chip select pins (CS and CS) permit easy stacking of devices for multi-channel multiplexing systems (see Applications Section, Figure 19). Two-Level Switching The two-level switching system of the DG535/536 (SW4 and SW5) works out of phase, effectively isolating half of the switch outputs from the drain (output) of the multiplexer. These series switches serve several functions: They provide an extra stage of off-isolation. They reduce the drain output capacitance significantly and increase the multiplexing transition speed. They reduce the off-leakage current, which reduces the offset voltage that develops from the total off-leakage current flowing through the load resistance and/or switch on-resistance. This enables lower analog signal levels to be handled accurately.
An additional feature, a DIS pin, is an open drain terminal with the source tied to the device substrate. The DIS terminal represents a high impedance to the substrate (normally ground) when the DG535/536 is disabled and a low impedance to ground when the DG535/536 is enabled. This output can be used to indicate which device in a large matrix has been enabled (see Figure 13), or it can be used to switch off circuitry following the multiplexer stages.
Silicon Gate Minimizing Parasitic Effects Polysilicon is used as the transistor gate material for the DG535/536, as opposed to more conventional metal-gate designs. This technology minimizes the charge coupling of the control-logic signals to the switch output due to the self-aligning properties of the process. Metal-gate technology relies on photolithographically aligning the gate metal with the channel diffusions, resulting in greater overlap tolerances. As shown in Figure 3, a PN junction exists between the p-type substrate and the n-type channel diffusions. This junction should not become forward biased by the analog signal going more negative than the substrate potential (normally ground). Device damage could result from the current flow through the forward biased substrate-channel junction, exceeding the aluminum current handling capacity (i.e. 20 mA). Analog signal dc biasing or offsetting the device power supplies can prevent this problem. These methods are discussed in the applications section of this paper (Figure 7 and Figure 8).
The insertion loss and bandwidth of the switch are improved with DMOS transistors that offer a low on-resistance and low intrinsic capacitance (see Vishay Siliconix SD5000 data sheet). On the DG536 channel-to-channel crosstalk is minimized by physically separating each input channel with a GND pin which extends to the device substrate. This, in conjunction with careful PC board layout (see Figure 6), can yield channel-to-channel crosstalk figures better than -92 dB at 5 MHz.
Further ac performance benefits are obtained through the n-channel DMOS transistor T configurations (Figure 2). This maximizes the off-isolation, since SW2 provides a shunt path to ground for any signals fed through the parasitic capacitance associated with SW1. SW3 (working in phase with SW1) provides an extra stage of off-isolation and prevents the shunt switch (SW2) from affecting consecutive channels.
Gate
Source Symbol
Drain
FIGURE 3. Cross-Section of an N-Channel, Silicon-Gate DMOS Transistor
www.vishay.com S FaxBack 408-970-5600 Document Number: 70608 03-Aug-99
6-2
EE EE EE E EE EEEEEEEEE EEEEEEEEEEEEE EEEEEEEEE EEEEEEEEEEEEE EEEEEEEEE EEEEEEEEEEEEE EEEEEE
Source/Body Gate Drain n+ n+ p+ p-Substrate
-- Aluminum
-- Gate Oxide -- Polysilicon -- Field Oxide
AN501
Vishay Siliconix
DG535/536 DC Characteristics
Power Supply Current Consumption
Until now, most available video multiplexers or digital crosspoint switches relied on high-level supply currents for operation. The DG535/536 requires a total supply current of only 5 mA, typical. This feature makes the DG535/536 ideal for systems with high channel density, such as 32-channel crosspoint matrices used in video mixing consoles or as ECL digital crosspoint replacements in large data transmission systems. The total supply current for a 32-channel crosspoint system using the DG535/536 is approximately 320 mA, much lower than other video multiplexers.
On-Resistance
On-resistance must be low to ensure low insertion loss, especially when the switch drives low load resistances. As shown in Figure 4, the on-resistance remains low and fairly constant over the usable analog signal range. This makes the DG535/536 useful for audio applications that require low harmonic distortion.
rDS(on) vs. VD and Temperature 400 360 320 V+ = +15 V GND = 0 V
DG536 AC Characteristics
280 r DS(on) (k W ) 240 200 160 120 80 40 0 0 2 4 VD (V) 6 8 10 -55_C 25_C 125_C
(Refer to the DG535 data sheet for the 28-pin DIP performance.)
Bandwidth
The "on" frequency response is expressed as the frequency at which the insertion loss (at dc) increases by 3 dB. The measured bandwidth of the DG536 is greater than 300 MHz.
Crosstalk
Crosstalk is the amount of unwanted signal apparent at a particular node due to the parasitic capacitance of the device. As the most important parameter for many applications, crosstalk is specified in a number of ways. 1. Single-channel crosstalk is the ratio of the signal seen at the drain (output) to the signal applied to a single off-channel input. This is expressed by
XTALK (SC)(dB) + 20 log10 VOUT VIN
FIGURE 4. On-Resistance vs. Analog Signal Characteristics
Nominal rDS(on) = 50 W VOUT
DrDS(on) v 2 W RIN 600 W VIN 1 Vp-p RL 600 W
VOUT Insertion Loss + 20 LOG 10 VIN
Most conventional multiplexers specify this parameter on the data sheet as off-isolation. This value for the DG536 is more than twice as good as other 16-channel analog multiplexer ICs, proving the effectiveness of the T switch. 2. All hostile crosstalk is the ratio of the signal measured at the drain to the signal applied simultaneously to all 15 channels (i.e., with one channel on). 3. Chip-disabled crosstalk is the drain output to signal input ratio. The input signal is applied to all 16 off channels simultaneously. 4. Adjacent input crosstalk is the ratio of the signal applied to a source (input) to the signal measured at any adjacent source. A low adjacent input crosstalk is required for video applications to avoid ghosting effects that may appear on video monitors or TV screens.
www.vishay.com S FaxBack 408-970-5600
FIGURE 5. 600-W Audio System
In a 600-W audio system, such as the one represented in Figure 5, the percentage of on-resistance change relative to the load resistance is only 0.33%. The insertion loss due to the switch on-resistance is 0.7dB.
Leakage Current
The DG535/536 features low off and on leakage currents, reducing switching errors.
Document Number: 70608 03-Aug-99
6-3
AN501
Vishay Siliconix
TABLE 1. CAPACITANCE VALUE FOR 16 CHANNEL MULTIPLEXERS Parameter
CS(off) (pF) CD(off) (pF)
DG526
10 65
DG506A
6 46
DG508A
5 26
CD4051/2/3
10 60
DG536
2 8
Note: These are typical values taken from data sheets
Switching Time
The DG535/536 switching time enables use of the device at high multiplexing rates. The low transition times (tON = 300 ns maximum and tOFF = 150 ns maximum) make it ideal for fast multi-channel analog or digital multiplexing. True break-before-make (BBM) switching action is guaranteed by design. This prevents shorting (crosstalk) of time adjacent input channels during transition.
S Coaxial interconnect of leads, plugs, and sockets. S Sockets should be avoided
Capacitance
Capacitance determines the loading effect of the multiplexer on signal sources and affects transition times, as well as system bandwidth. 1. Off-state input capacitance gives the loading of the device (in the off-state) to a signal source. With a typical value of 2 pF, this allows efficient paralleling of many device channels in multi-channel crosspoint matrices with negligible loading effects.
SMB-PCB Mounting sockets Top Side (Ground Plane)
3. Off-state output capacitance affects the transition speed of the multiplexer. The output capacitance must be charged and discharged in turning on and off a device; thus, a low value of capacitance enables rapid transition times. Table 1 shows a comparison of DG536 capacitance to comparable 16-channel multiplexers.
Applications Circuit Board Layout To optimize the high-frequency characteristics of the DG536, care must be taken in circuit board layout and interconnections. Parasitic stray capacitances caused by poor layout could degrade performance significantly. As shown in Figure 6, use of guard planes and traces between signal paths is a good layout practice. Other layout considerations include: S Short signal paths S Sufficient power supply decoupling
www.vishay.com S FaxBack 408-970-5600
Many applications for the DG535/536 will be in video related systems. Some examples of circuit configurations are included in this section.
Video
The DG536 was designed primarily for handling broadcast quality video signals. Optimum performance is achieved with a bias between +2.5 V and +3 V. Differential phase linearity is best at this bias level.
Document Number: 70608 03-Aug-99
6-4
EEEEEEEE EEEEEEEE
2. On-state input capacitance also determines the loading effects of the device on-signal sources and limits the number of parallel on channels allowed in a large matrix. In large matrixes buffering of the input signals is recommended.
PCB Bottom Side
DG536 Mounted on Underside of PCB
FIGURE 6. Circuit Board Layout for Optimal Performance (DG536)
AN501
Vishay Siliconix
A general-purpose 16-channel wideband multiplexer is shown in Figure 7. Dc biasing is achieved with the divider network R1 and R2. A wideband op-amp (CLC410) is configured to give an inverting unity gain, while removing the +3 V dc by setting the voltage on the non-inverting input to +1.5 V dc. The use of trimpot R7 and precision resistors allows accurate elimination of any dc bias. This arrangement results in faster multiplexing rates than capacitive decoupling while providing black-level clamping, impedance matching for 75 W loads, and greater drive for transmission stages, with no major compromise on signal quality (distortion, frequency response, etc.) Alternatively, the device supplies can be offset to eliminate the need for 16 separate bias circuits. Such an arrangement, shown
+ R1 39 kW 0.1 mF Video Input S2 R2 10 kW S16 A0, A1, A2, A3 S1 CS V+ D +15 V
in Figure 8, could be used in a security system or in a remote industrial monitoring system. The DG535/536 positive supply and ground pins (at -3 V) should be heavily decoupled to the video camera ground connections.
The switching threshold of the device at a supply voltage of +15 V is approximately between +6 V and +8.5 V above the substrate potential (Figure 9). Since the substrate is held at -3 V, the effective switching threshold referenced to ground is between +3 V and +5.5 V. Thus, the device can still be controlled from CMOS logic signals (provided that the logic 0 (VAL) is less than 3 V and logic 1 (VAH) is greater than +5.5 V).
+15 V
R5 470 W
R3 470 W R4 18 kW - CLC410 + R6 1.2 kW 75 W
Video Output
DG535/536
CS All GNDs EN ST
R7 (1 kW lin)
Address Bus Control Logic
FIGURE 7. General-Purpose 16-Channel Wideband Multiplexer
+12 V
1 2 3 4 EN S1 S2 S3 S4 CS ST V+ 75 W D CLC111 1 kW Video Monitor
Video Cameras
DG535/536
CS
-3 V
S16
All GND A0, A1, A2, A3 pins
16
Address Logic
FIGURE 8. A Closed-Circuit Monitoring System
Document Number: 70608 03-Aug-99 www.vishay.com S FaxBack 408-970-5600
6-5
AN501
Vishay Siliconix
V+
Logic Input Switching Threshold vs. Supply Voltage (V+) 13 GND = 0 V TA = 25_C
+5 V
11
VCC
VDD
V+
V TH (V)
9
TTL 4-Bit Binary Address Bus MC14504
DG535/536
ST
7
EN A3 A2 A1 A0 V-
5
3 8 10 12 14 16 18 V+ - Positive Supply Voltage (V)
FIGURE 9. Logic Input Switching Threshold vs. Supply Voltage
FIGURE 10. Using the MC14504 for Address Logic Level Shifting
In applications involving reduced supply voltages and offset conditions, the input switching threshold (VT) may be reduced below the CMOS logic "0". This may cause the address inputs to appear permanently as logic "1" regardless of the control logic states. Therefore, control logic level shifting may be needed. TTL to CMOS level shifting can be easily accomplished using inexpensive CMOS level shifters such as the MC14504 or CD40109.
the address inputs (A0 to A3) and applying the appropriate logic level to output select simultaneously. The circuit in Figure 11 also illustrates how the chip select inputs can be used. As shown in Figure 12, a 32-channel single-ended multiplexer can be configured without external chip select circuits. This circuit makes use of the CS and CS inputs which allow device selection from a single control line. The basic circuit shown in Figure 11 can be extended and elaborated to give a 16 x 16 matrix for video crosspoint applications such as central routers used in video studios. This circuit, shown in Figure 13, allows source (or video input) to be connected to any video output (or any number of outputs). The strobe input (ST) on each device is used to latch the appropriate address into that particular device. By strobing the required address into each device sequentially, any crosspoint connection can be made. The DG535/536 makes an excellent digital switch due to its low channel-to-channel crosstalk, high off-isolation, and wide bandwidth specifications. In digital data transmission systems, the DG535/536 can easily handle data rates in excess of 100 Mb/s. The circuit shown in Figure 13 can be used as a digital cross-point to replace expensive, power consuming ECL crosspoint ICs. Besides handling raw digital data, the DG535/536 can also be used for other forms of data transmission, such as FSK and PCM systems.
Document Number: 70608 03-Aug-99
Crosspoint Switching Many analog and digital systems, such as a central router used in a video studio console (Figure 8), require crosspoint switching functions. In this application, many channels route signals to many different outputs. Due to its small outline PLCC package and low power consumption, the DG536 leads itself easily to multi-channel crosspoint functions. Figure 11 illustrates how the DIS (disable) pin can be used to indicate which output is selected. When logic 1 is applied to output select, device 1 is enabled and device 2 is disabled. With device 1 enabled, the DIS pin is connected to signal ground, thus turning LED 1 on. With device 2 disabled (due to CS being 1), its DIS pin represents a high impedance to ground and LED 2 is off. Any one of sixteen inputs can be connected to either output. This is achieved by applying the appropriate CMOS logic address to
www.vishay.com S FaxBack 408-970-5600
6-6
AN501
Vishay Siliconix
+5 V 4 Si584 Buffers S1 V+ EN ST LED1 R1 D 16 Signal Inputs LED2 R2 OUTPUT1
DG535/ DG536 #1
DIS
CS S16 A0 to A3 GNDCS
S1 V+ EN CS ST D OUTPUT2
DG535/ DG536 #2
DIS CS S16 A0 to A3 GND OUTPUT SELECT "1" = 0/P1 Selected "0" = 0/P2 Selected
Address Logic
FIGURE 11. The DG535/536 as a 16
+15 V S1 Video Input Channels 75 W ST V- GNDS DG535/ DG536 D CH16 75 W Enable Device Select Address Bus +15 V CH17 75 W CS ST CSV+ S1 EN DG535/ DG536 D S16 GNDS A0 to A3 EN CS A0 to A3 Video Input Channels
2 Matrix Switch
Si584s S1 S2 S3 S16 DG535/ DG536 1 ST D1
CH1
DG535/ DG536 2 Video Output ST
D2 Video Outputs
Video Output Select DG535/ DG536 16 ST D16
Video Input Channels
CH22 75 W
Address Bus (Video Input Select)
FIGURE 12. 32-Channel Multiplexer
Document Number: 70608 03-Aug-99
FIGURE 13. 16
16 Video Crosspoint Circuit
www.vishay.com S FaxBack 408-970-5600
6-7
AN501
Vishay Siliconix
FSK Frequency shift keying (FSK), commonly used in data transmission networks, relies on representing the digital code with frequency sine wave bursts. An FSK multiplexing system block diagram is shown in Figure 14. Each digital level has a specific signal frequency. The DG535/536 can be used to multiplex 16 different digital channels into a single transmission line or into a transmitter. Similarly, a DG535/536 may be used to demultiplex the data at the receiving end. Since the device can manipulate higher frequency sine waves, data can be transmitted at a higher rate than with a conventional multiplexer. distribution frame. Similarly, code converters are required to reconvert the binary PCM into ternary PCM for transmission. Unlike digital switches which require specific digital signals, using the DG535/536 in the distribution frame (Figure 17) eliminates the need for code conversion and meticulous regeneration because it can handle analog signals.
Programmable Gain Video Amplifier The circuit shown in Figure 19 uses the DG536 as a binary gain select for a video/wideband op-amp (CLC410). The gain of the Si582 is set by:
PCM A more commonly used and faster form of digital data transmission is known as PCM (pulse coded modulation). Used in telecommunications systems, PCM converts analog speech signals into 8-bit digital words for serial transmission. The data transfer rate used (for 4 kHz bandwidth voice signals) is up to 274.176 Mbps. The DG535/536 can be used to route PCM signals in main telephone exchanges, replacing bulky hard-wired distribution frames. PCM highways can thus be rerouted remotely, under computer control, rather than manually. RZ (returns to zero) PCM data consists of three discrete (ternary) levels to overcome long periods of zeroes (Figure 13). Digital signals can degrade beyond legibility after only a few hundred yards of travel down a transmission line. Therefore, the PCM signals must be regenerated at regular distances to avoid excessive distortion. Figure 16 shows the architecture of a conventional binary distribution frame in a telephone exchange. Signal regeneration is applied to handle degradation during transmission and routing. Code converters are required to change the ternary PCM into binary PCM for routing within the
FSK Output e.g. 1011 FSK Generator FSK Generator FSK Generator S1 S2 S3 DG535/ DG536 D
AV + 1 )
Rf Rg
For example, listed below in Table 2 are the results when Rf = 470 W.
TABLE 2.
Gains For The Circuit of Figure 19 Logic Input
0000 0001 0010 0011
Rg
47 kW 4.7 kW 2.4 kW 1.6 kW
Gain (AV)
1.0 1.1 1.2 1.3
The low on-resistance of the DG535/536 gives good gain stability, and the resistor tolerances mainly determine the gain error of the circuit. The wideband qualities of the CLC410 allows this circuit to be employed for digital level correction in any video systems including broadest quality specifications.
Digital Input Channels
Output to Transmission Line or Transmitter Input Stage
Binary PCM a) Analog voice signal converted to digital signal using 8 bits per sample Ternary PCM b) Digital signal transmitted and clock regenerated from digital signal to get synchronization
S16 FSK Generator (f0) (f1)
A0 to A3
Frequency Synthesizer
Address Bus
FIGURE 14. FSK Multiplexing System Block Diagram
www.vishay.com S FaxBack 408-970-5600
FIGURE 15.
Document Number: 70608 03-Aug-99
6-8
AN501
Vishay Siliconix
PCM Highway Remote Exchange/ Switch or Digital PBX or Concentrator PCM Highway from codecs within main exchange Central office or main telephone exchange Remote Exchange/ Switch or Digital PBX or Concentrator
Regen -erator (1)
Regen -erator (2)
Code Converter
Binary Distribution Frame
Code Converter (2)
Regen -erator (3)
Couple hundred yards/different floor FIGURE 16. Binary PCM Routing Network
PCM Highway Remote Exchange/ Switch or Digital PBX or Concentrator
PCM Highway from codecs within main exchange
Central office or main telephone exchange Remote Exchange/ Switch or Digital PBX or Concentrator
DG535/536 Crosspoint
FIGURE 17. DG536 PCM Distribution Frame
Video In + 75 W CLC410 - 470 W Rf S1 S2 S3 S4 S5 D S16 DG536 A0 to A3 Logic Input Gain Set RP RA RB RC RD RE R g + r DS(on) Video Out 75 W
Digital Signal Processing Board Under Test
DG535/536
S1 S2 D
S16 A0 to A3 Address Bus
16-Bit Data Bus
MicroProcessor
Data Logging
FIGURE 19. Programmable Gain Video Amplifier
FIGURE 18. ATE Applications
Document Number: 70608 03-Aug-99
www.vishay.com S FaxBack 408-970-5600
6-9
AN501
Vishay Siliconix
ATE A simple but accurate ATE system, as shown in Figure 18, can be designed for testing digital processing boards. The propagation delay time for each of the 16 digital signal paths can be tested individually, with negligible errors due to the very small propagation delay through the DG535/536. Also, the variation of delay times from channel to channel is less than 0.25 ns. The data latches are activated by the DG535/536 strobe input (ST). The latch is transparent when ST= logic 1, thus the device responds to changes of data at the address inputs. When ST = logic 0, the previous data is latched into the device, regardless of new data appearing at the address inputs. The DG535/536 timing arrangements meet the requirements of popular microprocessors, such as the 8085A, 6800, and Z80. The 8085A to DG535/536 interface is shown in Figure 20, and Table 3 illustrates the timing compatibility of the DG535/536 with the 8085A and the faster 8085A-2 devices.
TABLE 3.
Microprocessor Interface On-chip data latches in the DG535/536 simplify interface with a microprocessor data bus. This eliminates the need for peripheral memory devices (such as I/O ports or D-type latch ICs) to maintain switch addressing while the processor uses its data bus for other functions.
5V +15 V
Timing--DG538/536 With Popular Microprocessors Specification
tSW (strobe pulse width) tDW (data valid to strobe) tWD (data valid after strobe)
8085A ns/min.
400 420 100
8085A-2 ns/min.
230 230 60
DG536 ns/min.
200 100 50
+15 V
Data Bus WR 8085A mP System Bus Address Bus CS Address Decoder
MC14504
A0 A1 A2 A3 EN ST
V+
CS S1
S16 D CS D
DG535/536
GNDs
FIGURE 20. 8085A to DG535/536 Interface
+15 V R1 R2 R3 R4 R5 A0 A1 A2 A3 EN +15 V CD7407 V+ CS S1
Data Bus
DG535/536
R6 ST D CS
S16
6800 mP System Bus Control Bus
F2 = DBE
D
GNDs R/W
Address Bus
CS Address Decoder
R1 to R6 = 100 kW
FIGURE 21. 6800 to DG535/536 Interface
www.vishay.com S FaxBack 408-970-5600 Document Number: 70608 03-Aug-99
6-10
AN501
Vishay Siliconix
Figure 21 shows the complete 6800 to DG536 interface circuit. In order to have a data valid signal, it is necessary to nand the R /W/CS gate output with the F2 clock (usually connected to the DBE pin). This makes the interface circuit functionally compatible with the 8085A interface shown in Figure 20. Note that open collector gates and buffers could be used to level shift the TTL logic levels from the microprocessor to the CMOS levels required by the DG535/536 logic inputs. To achieve the correct ST signal in a Z80 processor system, the WR and MREQ signals must be gated with the standard CS signal, as shown in Figure 22. moelectric offset voltage. For the DG535/536, the thermal EMFs produced on chip are small since the device exhibits a low power consumption (75 mW), producing a low temperature on the die. 2. Leakage current offset is caused by leakage current flowing through the rDS of an on-switch and/or the load resistance.The offset voltage developed due to leakage current is negligible since the device has very low leakage currents (a benefit incurred by the two-level system) coupled with very low on-resistance. For example: V (offset) = ID(on) x rDS(on) = "100 pA (typical @ 25_C) = "5.5 nV (typically)
55 W (typical)
Low Analog Signal Switching/Multiplexing The DG535/536 has several uses in handling low-level analog signals (such as in medical equipment or ultrasound transducer multiplexing) because the device exhibits inherently low noise and offset voltages. Two factors affect offset voltage: 1. Thermoelectric offset voltage is produced by the incidental thermocouples that exist within the integrated circuit. There are many intermetallic junctions within an IC. These junctions act as an individual thermocouple and has an identical reversed counterpart. That is, from source to drain, we have gold-aluminum/aluminum-silicon and silicon-aluminum/ aluminum-gold. Therefore, if the temperature surrounding each junction is constant and equal, the thermal EMFs cancel each other, giving a zero net offset voltage. Since a thermal gradient always exists across the chip, then there is always a net ther-
The circuit shown in Figure 23 can be used to remotely monitor up to 16 different thermocouples with high accuracy. The output of the thermocouples is in the form of a small dc voltage, on the order of millivolts, with typical voltage changes on the order of tens of microvolts per _C. Thus, voltage offset developed by the switching devices can frequently limit system accuracy. Using the differential multiplexing technique shown in Figure 23, high resolution can be achieved since the thermal EMFs produced by each DG535/536 are canceled as common mode voltages at the instrumentation amplifier inputs. To minimize pick-up and noise effects, the same PC board layout rules apply for this type of circuit. Best accuracy is achieved by ensuring that the multiplexers are kept close together in a thermally stable environment.
+15 V
R1
R2
R3
R4
R5 A0 A1 A2 A3 EN V+ CS S1
Thermo- Couples (X 16)
DG535/ DG536 S1 S2 D
Differential Instrumentation Amplifier + -
Data Bus +15 V R6 Z80 mP System Bus WR
S16 A0 to A3
CD7407
DG535/ DG536
ST D
S16 D
MREQ Address Bus
GNDs CS
DG535/ DG536 S1 S2 D
CS Address Decoder
S16 A0 to A3 Channel Select
FIGURE 22. Z80 to DG536 Interface
Document Number: 70608 03-Aug-99
FIGURE 23. Thermocouple Multiplexing System
www.vishay.com S FaxBack 408-970-5600
6-11

▲Up To Search▲

Price & Availability of AN501

	To Download AN501 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .